To clean a Whirlpool dishwasher door gasket, open the door, wipe the whole rubber seal, including the folds, with a soft cloth and warm soapy water, wipe the edge of the tub and the inner rim of the door the same way, rinse the cloth and wipe again, then dry. Do it when the dishwasher is empty and cool. Our Whirlpool dishwasher leaking guide calls a worn, dislodged or food-caked door seal the single most common leak source at the front of the door, so a clean gasket is worth a minute of your time each month.
Why does a dishwasher door gasket get dirty?
The gasket is the rubber seal that runs around the door opening and presses against the tub when the door closes. It sits right where steam, grease and food splashes end up. Small bits of food, soap film and mineral residue collect in its folds, and in a damp, warm spot a dark film can develop. That film can smell, and a seal caked with food can stop pressing evenly against the tub. The edge of the tub and the inner rim of the door catch the same residue.
The residue is a sign of how much food is reaching the door area, so scraping plates and using the right detergent help. Using regular dish soap instead of dishwasher detergent creates foam that pushes water past the seal, according to our leaking guide, so keep dish soap out of the machine.
How do you clean the gasket and the tub edge?
- Make sure the dishwasher is empty, the cycle has ended and the machine has cooled.
- Mix warm water with a little mild dish soap.
- Use a soft cloth or a soft brush to wipe the gasket. Work along the whole seal, and get into the grooves and folds, where residue hides.
- Wipe the edge of the tub, the lower lip of the door and the area around the latch with the same cloth.
- Rinse the cloth in clean water and wipe the surfaces again to remove the soap.
- Dry the seal and edges with a clean towel, and leave the door ajar for a while to let the air in.
Do not pull the gasket out of its channel to clean behind it unless your manual says to. A seal that has been pulled loose can leak when you close the door.
What about stubborn film and smells?
A dark film or a stale smell usually comes from residue in the folds, not from the machine’s insides. Wipe it again with soapy water and a soft brush that will not scratch. Be careful with strong chemicals: check your owner’s manual before using bleach or a harsh cleaner, because some products damage rubber or other parts. Our Whirlpool dishwasher filter cleaning guide says a clogged filter is behind many odor complaints, and suggests wiping the door gasket and running a dishwasher-cleaner cycle during that regular upkeep, so check the filter as well.

What does a worn or damaged gasket look like?
Look for cracks, tears, flattened spots, a seal that has come out of its channel, or hard and brittle rubber. Close the door on a clean, dry seal and look for gaps where the seal does not touch the tub. Water on the floor at the front of the dishwasher after a cycle is the classic sign. Our Whirlpool dishwasher leaking guide separates the door, a hose and an internal leak by where the water appears: front-of-door water points to the gasket or the loading, and water from underneath points to an internal hose or pump.
A cleaned seal that is still torn will still leak. Replacement is a part job. Ask your technician, or follow your manual if it describes a seal that the owner can replace.
How often should you clean the gasket?
A wipe once a month is a sensible habit, and it fits well with the monthly filter check. Wipe sooner if you notice a film, a smell or water at the front. If you run heavily soiled loads often, check it more often. If it smells damp, leaving the door slightly open to dry is fine, but keep it latched if small children or pets are around.
Our dishwasher how-it-works guide explains what happens in a cycle, which helps you see why the seal area gets the steam.
When should you call a technician?
Call if the gasket is torn, loose or hardened, if the door leaks after a cleaning, if the door does not latch or close evenly, or if the dishwasher shows a flood code. Stop using a dishwasher that leaks onto the floor. If water gets near an outlet, switch off the breaker at the panel while standing on a dry floor and never pull a plug from a wet outlet. Do not take the door apart or remove panels yourself. Our Whirlpool dishwasher repair page explains how a visit works.